How to Replace the Replacement Key Battery For the saab car key 9-3

Saab owners have to follow a series of special steps to install a second ignition key. This requires an electronic handheld computer, referred to as Tech-2, to be used by the dealer. Then a new car key and transponder are required to be purchased and then programmed into the car.

It is recommended to rotate your keys in order that one does not get worn out more quickly than the other. This will help to keep your keys in pristine condition.

Replacement Case

In contrast to the traditional Saab keys of old, the new key fobs contain electronics which makes it hard to duplicate. That has made car theft a lot more difficult than it was a few years ago. It has also made it more expensive to replace keys lost.

saab keys replacement 9-3 owners must have two keys working. It costs a fortune to replace a lost key, as it requires replacing the CIM module, and programming the locking cylinders. Dealers typically charge between $100 and $200 to do this.

There are ways to avoid these costly costs. Some parts retailers will look up the code from an old key (usually the same one that opens the doors and turns off the ignition) and cut a new metal key blade for a fraction of the dealer's cost. The key must be the exact same as the original for it to function in your vehicle.

You can also change the case yourself by following these steps. You'll require a flathead screwdriver as well as some patience. Using the screwdriver, slowly break the plastic and remove the emergency key from the case. Once you have the case open, remove the electronics and put them back into your new case. Make sure you put the correct key and badge back into the case as well.

Replacement Battery

The replacement battery for the Saab 9-3 is a cheap part that can be replaced quickly and easily. Cyclone's YouTube video Cyd shows how to replace the battery for the remote fob in just four easy steps. This tutorial should work with any modern Saab key fob. However, the process could differ slightly.

The button is typically located just below the Saab logo on the back of the fob. This button is typically located on the back of the fob, close to the Saab Logo. Then take a flathead screwdriver to insert into the small hole of this button. This should be enough to open the fob case in order to change the battery.

After you have installed the battery CR1632, you are able to rebuild your remote key fob. Then, you can program it into your car. The procedure should take no more than an hour or less. This is a simple process that doesn't require any special tools.

If you lose a key the process will be slightly more complicated but it is still able to be accomplished. The dealer will first need to read the VIN of the vehicle and order a replacement TWICE module and key blade with the correct unique code. The dealer will then have to program the key using MDI, a brand new software tool.

Replacement Key Fob

The key fob is equipped with a battery that is used to lock and unlock your car. The batteries last for a certain time, and they will eventually go out of service. It's a common issue that affects all cars. The good news is that you can replace the battery on most key fobs without having to replace the entire case. Amazon sells replacement fobs that have all the electronics in place. You can simply open the case and replace the batteries. It is important to keep in mind that you'll have to take out the emergency key first. you can accomplish this by inserting the screwdriver of a small flathead into the slot found in the middle of the case. Move the screwdriver around the case, and it will split open, making it easier to take it out.

If you're ready to change your keys, have a spare available. This will save you a lot of money. If you have an extra key, you can request the dealer to cut it and program it for your vehicle. This is less expensive than purchasing a new fob.

It is possible to add another key to your car in the event that you don't have one, but it takes an extensive amount of research and effort. It costs a few hundred dollars to purchase a second car key. The computer in the vehicle must also be programmed. Professionals can accomplish this however it's a costly option.

Replacement Ignition

In contrast to earlier Saab cars, the modern saab key fob repair 9-3 models are equipped with a much more sophisticated alarm system that is built around a coded key. This means that should you lose only one working key, acquiring another key can be extremely expensive since the car has to have a specific computer module installed and it must also be specifically programmed to accept an extra key. Even a dealer can charge hundreds of dollars to program an additional key if they are unable to complete the task.

If you've lost your sole working key and a dealer is able to replace your car's computer (known as the CIM or SAAB TWICE) in order to make a replacement, and they will charge you the highest price for it. Instead we can reprogram the EEPROM on your existing car computer to allow it to be programmed for a replacement key, saving you over 50% of the amount you spend at a dealer.

If you've been a long time owner of an 03-11 SAAB 9-3, then you likely have noticed that the ignition switch isn't really all that robust. If your ignition key is not working correctly, you should consider replacing it. They can become sticky and the buttons have been known to fall off. The good news is that replacing the ignition key isn't as difficult as it seems and can be done quickly with the appropriate tools.