How to Replace a Kia Sportage Replacement Key

The key in many Kia models comes with the keyless entry feature built into. This key is similar to remote controls and can be exchanged with a Kia dealer.

Key fobs may stop working due to a variety of reasons, including batteries that are dead, worn-out buttons signal interference or water damage. Here are some suggestions on how you can get your Kia Sportage replacement key to work again.

How do you replace the remote key or smartkey?

It doesn't matter if your Kia comes with an intelligent key, remote key push-to-start keys, or a regular non-transponder steel key, the battery in these keys will eventually need replacement kia car keys. This is particularly relevant if your car displays a message indicating that the smart or remote key is not powered by the battery.

This is a relatively simple procedure. To replace the battery in the key fob remove the mechanical key from the slit in the back of the key fob. Next, lift the cover. A small screw will be located inside the key fob to hold the battery in its place. Remove the old battery by unwinding the screw with a small screwdriver. Install the new battery and close the cut on the key fob.

Once the key fob has new batteries Test it by pressing the lock and unlock buttons. You're in good shape when the doors lock or unlock as you expect. You can now use the hands-free feature to lock and unlock your kia rio Key whenever your fingers start to get cold or when you need to complete errands in Brandon.

Note: Some key fobs (transponder chip or smart keys) may need to have their programming completed. This requires a specific programming a kia key fob machine that only the dealer or locksmith can access. Other keys (non transponder keys made of metal) don't require programming. If your key requires to be reprogrammed, then you will need to be aware of the number stamped on the key code tag and save it in a safe location.

How do I replace a battery

If the Kia key fob is unable to respond to pressing the lock or unlock button, it's a sign that the battery is low. A low battery may also cause other issues, such as the check engine light flashing on or the engine not cranking. Fortunately, replacing the key fob battery is a fairly simple DIY task that requires only some basic tools.

Before starting the process be sure that your vehicle is off and all doors are shut. Find the small, metal or plastic piece near the bottom of the key fob. Jiggle it until the key falls out. The key can be put into the driver door handle to unlock your car.

To replace the battery on the key fob, take off the cover at the rear. Make use of a plastic pry tool to loosen up the latch that holds the black negative cable. Remove the old battery and orient the new one to ensure that the "+" positive side is facing you, and the "negative" negative side is facing towards the fob's electrical contacts made of metal. Avoid using too much force when pushing the new CR2032 into place to avoid damaging or breaking the metal contacts.

Once the new battery is installed and the key fob is turned on, turn it off and back on in the ignition until the door locks. Then you can test your Kia key fob to determine if it is working properly again.

How to replace the smart key?

You may have either the standard keyfob or Smart Key based upon the model of kia soul replacement key Sportage. The difference between these is that the smart key is equipped with a small mechanical key blade tucked inside it, while the standard fob doesn't. Both key fobs contain batteries that eventually require changing. It is a simple process that takes less than two minutes.

Before you begin it is essential to ensure that you are on a level surface with good lighting and that the Kia is off. Be aware that the fob can contain tiny pieces that could fall should you not be careful.

The small release button is located on the lower backside. This will either be a circular silver button or a rectangular slot. When you press it mechanical key blade, it will come out and you can then open the key fob.

Once you have the key fob opened, you can simply take off the old battery and replace it. The new battery is a CR-2032 that can be purchased online or at your local auto parts store. Once you're done, you should be able to lock, unlock and start your vehicle with your key fob - even if your engine isn't running!

How to replace the mechanical key

The Kia keyfob is a wonderful convenience which allows us to lock or unlock our car by simply pressing the button. But, as with all devices there are issues with it occasionally. Luckily, there are ways to resolve these issues and ensure that our key fobs are in good condition for the long run.

One of the most frequently encountered issues is a low or dead battery. This can cause your device to stop working or operate intermittently. If this is the issue, replace the battery with a new one.

If this doesn't resolve the issue Try using a standard flathead screwdriver and wedge it into the fob's plastic casing. Be careful not damage any internal components or scratch the plastic. Once open, carefully remove the old battery and replace it with a new one.

After the new battery has been put in, shut and open the doors using the mechanical key (every kia fob has an emergency mechanical key that will fit into the slot). Test the fob to make sure it's working as intended. Contact a dealer or a locksmith to address the issue if the fob is still not working. To avoid future lockouts, ensure that you have an emergency key that will work in all of the trunk and door cylinders.