How to Replace a Kia Sportage Replacement Key

The key of a lot of Kia models has the keyless entry feature built in. The key functions like remote controls and can be exchanged with an Kia dealer.

Key fobs may stop working due to a number of reasons, including batteries that are dead, worn-out buttons signal interference, or water damage. Here are some suggestions on how to get your Kia Sportage replacement key back to working.

How to replace a remote key or smartkey

It doesn't matter if your Kia comes with an intelligent key, remote key, push-to-start key, or a regular non-transponder steel key The battery inside these keys will eventually need replacing. This is especially when the car displays a message indicating that the remote or smart key is not powered by the battery.

Luckily, this is a relatively simple process. To replace kia key the keyfob battery remove your mechanical key from the slit on the back of the fob. Then, you need to pry the cover open. Inside the key fob, there will be a small screw that holds the battery in its place. Take out the old battery by removing the screw using a small screwdriver. Then, insert the new one and close the slit on the key fob.

Test the key fob by pressing the lock/unlock buttons. You're good to go when the doors lock or unlock as expected. You can now use the hands-free feature to lock and unlock your kia ceed key fob replacement whenever your fingers feel chilly or when you need to do some errands in Brandon.

Note: Some key fobs could need to be programmed (transponder chips or smart keys). This requires a particular programming machine that only the dealer or locksmith can access. Other keys (non transponder keys made of metal), do not need programming. If your keys need to be programmed again, you will need to be aware of the key code number stamped on the key code tag and record it in a safe location.

How to replace the battery

If your 2017 kia sportage key fob programming smart key replacement - take a look at the site here - key fob is not responding when you press the lock or unlock button on the fob, this is a signal that the battery needs to be replaced. A low battery can also cause other issues, such as the check engine light flashing or the engine not running properly. Fortunately, replacing the key fob battery is a relatively simple DIY project that requires just some basic tools.

Make sure you turn off your vehicle and shut all doors prior to starting. Find the small, metal or plastic piece at the bottom of your key fob and jiggle it until a metal key pops out. The key can be put into the driver door handle to unlock your car.

To replace the key fob battery, take off the cover at the rear and use a plastic bar tool to release the latch that holds the black negative battery cable. Remove the old battery and then align the replacement battery so that its "+" side is facing you, and the "-", negative side is facing the fob's electrical contacts. Avoid using excessive force when pushing the new CR2032 into position to avoid damaging or breaking the metal contacts.

After installing the new battery, turn the key fob on and off in the ignition until the door locks up. Then, you can test your kia rio key replacement cost key fob to determine whether it's functioning properly again.

How do you replace the smart key

You can have a standard keyfob, or a Smart Key based on the model of Kia Sportage. The smart key is equipped with an embedded mechanical key blade unlike the standard key fob, which does not. Both key fobs are equipped with an internal battery that will eventually need to be changed. Luckily, this is a fairly simple process that takes just two minutes.

Before you start before you begin, ensure that you are on a level surface with good lighting and that your Kia is off. Be aware that the fob has tiny parts that could fall if you're not careful.

The release button for the small size is located on the lower backside. It's either a circular button or a rectangular slot. Once you press this button, the mechanical blade will come out and you will be able to open the key fob.

Once you have the key fob opened and you are able to remove the old battery and replace it. The new battery is a CR-2032, and can be purchased online or in your local auto parts shop. After you've finished it should be possible to lock or unlock your vehicle with your key fob, even if your engine isn't running!

How do I replace the mechanical key?

The Kia key fob is a great convenience that lets us lock and unlock our car at the click of the button. Like any other device like a key fob, the Kia can occasionally have problems. There are ways to address these issues and keep your key fobs running for an extended period of time.

A dead or weak battery is among the most common problems. This could cause the fob to cease working or even to stop working intermittently. If this is the problem, replace the battery with a new one.

If this doesn't solve the issue, you can use a standard flathead screwdriver to wedge the fob's plastic casing open. Be cautious not to damage any internal components or scratch the plastic. After the battery has been removed, replace it with a new one.

Close and open the door with the mechanical key. (Every Kia fob comes with an emergency mechanical key which will fit into the slot). Test the fob to make sure it's functioning correctly. Contact a dealer or a locksmith to address the issue in the event that the fob is not working. To avoid lockouts in the future, ensure you purchase an emergency key that will be able to work with all trunk and door cylinders.